STW 0195, STW 0196

Rexroth
  • Size 6, 10
  • Component series 2X, 1X

eneral

Type STW 0195 STW 0196
Size 6 10
Installation position any, preferably horizontal
Ambient temperature range °C -20 … +50
Storage temperature range °C -20 … +80
Weight kg 2.4 6.5

hydraulic

Size 6 10
Maximum operating pressure Port P (sensor 50 bar) bar 50
Port P (sensor 160 bar) bar 160
Port P (sensor 250 bar) bar 250
Port T (sensor 50 bar) bar 50
Port T (sensor 160 bar) bar 160
Port T (sensor 250 bar) bar 210
Port A (sensor 50 bar) bar 50
Port A (sensor 160 bar) bar 160
Port A (sensor 250 bar) bar 250
Port B (sensor 50 bar) bar 50
Port B (sensor 160 bar) bar 160
Port B (sensor 250 bar) bar 250
Nominal flow P → A l/min 65
A → T, B → T l/min 60
Control spool 1 P → A l/min 10
A → T l/min 20
Control spool 2 P → A l/min 20
A → T l/min 20
Maximum flow See performance limits
Hydraulic fluid see table
Hydraulic fluid temperature range °C -20 … +80
preferably °C +40 … +50
Viscosity range mm²/s 20 … 380
preferably mm²/s 30 … 46
Maximum admissible degree of contamination of the hydraulic fluid, cleanliness class according to ISO 4406 (c) 1) Class 20/18/15 according to ISO 4406 (c)
Hysteresis % ≤ 0.1
Range of inversion % ≤ 0.05
Response sensitivity % ≤ 0.05
Zero shift upon change of Hydraulic fluid temperature %/10 K ≤ 0.15
Operating pressure %/100 bar ≤ 0.1
1) The cleanliness classes specified for the components must be adhered to in hydraulic systems. Effective filtration prevents faults and simultaneously increases the life cycle of the components. For the selection of the filters, see www.boschrexroth.com/filter.
Hydraulic fluid Classification Suitable sealing materials Standards
Mineral oil HL, HLP, HLPD, HHVLP, HVLPD NBR / FKM DIN 51524
Bio-degradable Insoluble in water HETG NBR / FKM ISO 15380
HEES FKM
Soluble in water HEPG FKM ISO15380
Containing water Water-free HFDU, HFDR FKM ISO 12922
Containing water HFC (Fuchs Hydrotherm 46M, Petrofer Ultra Safe 620) NBR ISO 12922
Important information on hydraulic fluids:
For more information and data on the use of other hydraulic fluids please contact us.

There may be limitations regarding the technical valve data (temperature, pressure range, life cycle, maintenance intervals, etc.).

The flash point of the process and operating medium used must be 40 K over the maximum solenoid surface temperature.

Flame-resistant – containing water:
Maximum pressure differential per control edge 50 bar
Pressure pre-loading at the tank port > 20% of the pressure differential, otherwise increased cavitation
Life cycle as compared to operation with mineral oil HL, HLP 50 % to 100 %

Bio-degradable and flame-resistant – containing water: If this hydraulic fluid is used, small amounts of dissolved zinc may get into the hydraulic system.

electrical

Size 6 10
Voltage type Direct voltage
Maximum current consumption of the amplifier A 2
of the amplifier (impulse current) A 3
Maximum current Output stage A 1.7
Signal part A 0.3
Actuated time 1) % 100
Maximum coil temperature 2) °C 150
Protection class according to DIN EN 60529 IP65 (If a suitable and a correctly mounted mating connector are used.)
Power supply V 24
Supply voltage range V 19,4 … 35
Admissible residual ripple Vpp 2
Earthing (GND) V 0
Enable input range “A6” V 9 … 35
“F6” V 9 … 35
Command value input UQ “A6” mA 10
Command value input range UP “A6” mA 0 … 10
IQ and IP “F6” mA 4 … 20
Actual value output UQ “A6” V ± 10
Actual value output range UP “A6” mA 0 … 10
IQ and IP “F6” mA 4 … 20
Control voltage Level as for pin 1
0 V reference potential For pins 3, 6, 8 and 11 (connected to pin 2 in valve)
Error output 24 V (19.4 V to 35 V), 200 mA maximum load
1) Connect the valve to the supply voltage only when this is required for the functional sequence of the machine.
2) Due to the surface temperatures occurring at solenoid coils, the European standards ISO 13732-1 and ISO 4413 need to be adhered to.

Sensor technology

Overload protection Sensor 50 bar bar 110
Sensor 160 bar bar 320
Sensor 250 bar bar 500
Bursting pressure Sensor 50 bar bar 200
Sensor 160 bar bar 640
Sensor 250 bar bar 1000
Characteristic curve deviation % < 0.2
Hysteresis % < 0.1
Repetition accuracy % < 0.05
Setting time (10 … 90 %) ms < 1
Long-term drift (1 year) under reference conditions % < 0.1
Conformity CE according to EMC directive EN 61000-6-2 / EN 61326-2-3 and EN 61000-6-3 / EN 61326-2-3
Category: