No products in the cart.
Product Carousel Tabs
Product Carousel Tabs
Mechanical Power Transmission Coupling
Geared Coupling
Flexocon Geared Couplings is used to join two rotating shafts for efficient transmission of Mechanical Power. Flexocon full gear Flexible Gear Coupling consists of two identical toothed hubs, two identical flanged sleeves with internal teeth, a gasket, a set of bolts, nuts and spring washers, lube plugs and two oil/grease retaining O-ring over the hubs…
SKU: n/a
Expansion Joints
Metallic Expansion Joints
Metallic Expansion Joints are made as per EJMA standard. These expansion Joints are made from Cold rolled Austenitic Stainless steel 304, 316 and 321 material and are suitable for higher Temperature as well as higher pressure. Any size and configuration can be manufactured as per customer requirements.
SKU: n/a
Mechanical Power Transmission Coupling
Pin Bush & Tyre Coupling
Flexocon Pin bush type flexible Couplings are of the cushioned drive type, transmitting the torque, through high Tensile bolts to the machine input shafts. Special Rubber Compounds are used in bushes so that it can absorb slight misalignments, tensional vibration and shock loads. The flanges are made of high grade cast iron. For special applications cast steel flanges are also manufactured.
Flexocon offer 20 standard models of Pin bush coupling with rating range from 0.81 KW to 249 KW at 100 rpm.
Flexocon also manufacture Pin bush type Brake Dum cum flexible couplings of different diameter to suit standard as well as non standard brakes.
Features
Features
No lubrication required. Accommodates misalignments. Damps out vibration. Reversing resiliency against shocks. Easy installation and removal. Inexpensive.
SKU: n/a
Expansion Joints
Metallic Expansion Joints
Metallic Expansion Joints are made as per EJMA standard. These expansion Joints are made from Cold rolled Austenitic Stainless steel 304, 316 and 321 material and are suitable for higher Temperature as well as higher pressure. Any size and configuration can be manufactured as per customer requirements.
SKU: n/a
Mechanical Power Transmission Coupling
Geared Coupling
Flexocon Geared Couplings is used to join two rotating shafts for efficient transmission of Mechanical Power. Flexocon full gear Flexible Gear Coupling consists of two identical toothed hubs, two identical flanged sleeves with internal teeth, a gasket, a set of bolts, nuts and spring washers, lube plugs and two oil/grease retaining O-ring over the hubs…
SKU: n/a
Mechanical Power Transmission Coupling
Pin Bush & Tyre Coupling
Flexocon Pin bush type flexible Couplings are of the cushioned drive type, transmitting the torque, through high Tensile bolts to the machine input shafts. Special Rubber Compounds are used in bushes so that it can absorb slight misalignments, tensional vibration and shock loads. The flanges are made of high grade cast iron. For special applications cast steel flanges are also manufactured.
Flexocon offer 20 standard models of Pin bush coupling with rating range from 0.81 KW to 249 KW at 100 rpm.
Flexocon also manufacture Pin bush type Brake Dum cum flexible couplings of different diameter to suit standard as well as non standard brakes.
Features
No lubrication required. Accommodates misalignments. Damps out vibration. Reversing resiliency against shocks. Easy installation and removal. Inexpensive.
SKU: n/a
Product Carousel Tabs
Universal Joints
Americardan 2000 Series U Joints
The Ameridrives Universal Joint is available in seven basic bearing designs:
Sizes U2131-U2155: Needle bearing design. Bearing caps are retained by snap rings.
Sizes U2160-U2188: Needle bearing design. Bearing caps are retained by bolts.
Sizes U2192: Uses two rows of roller bearings. Bearing caps are retained by snap rings. Lube fitting in center of cross.
SKU: n/a
Universal Joints
Americardan 5000 and 3000 Series U-Joints
Designed for operation at high misalignment angles up to 15º. Bearing and seal design resists lubrication loss and contamination. Ideal for use in severe atmospheric conditions. Superior materials and tight tolerances have proven to reduce vibration levels in rolling mills.
5000 Series are high torque designs ideal for applications with diameter restrictions such as cold mills. Catalog sizes range from 225 mm to 860 mm swing diameters and peak torque capacities up to 5647 kNm. Higher torque, custom designs are available in excess of 1200 mm swing diameter.
3000 Series are rated for high misalignment angles and are available in catalog sizes from 55 mm to 860 mm swing diameters and peak torque capacities up to 3153 kNm. Higher torque, custom designs are available in excess of 1000 mm swing diameter. Sizes 3440 and larger incorporate a unique inner race design within the bearing package to reduce routine repair costs by approximately 50%.
SKU: n/a
Universal Joints
Americardan J Series Universal Joints
Model J Series U-joints use only high-wing bearing cap design. Developed for operation misalignment at high angles up to 15º. Bearing and seal design resists lubrication loss and contamination. Ideal for use in severe atmospheric conditions.
SKU: n/a
Diaphragm Couplings
Ameriflex® Diaphragm Couplings
Since its introduction in 1971, the Ameriflex multiple convoluted diaphragm coupling has continued to set new standards for life and reliability in high performance machinery applications. Today, by using the latest design and manufacturing technology, Ameridrives Couplings is able to offer increased diaphragm coupling performance without compromising this outstanding reliability.
Advanced analysis and manufacturing processes have produced increased ratings without reducing safety factors. The use of the latest finite element analysis methods verified by strain gage and dynamic testing has allowed for a more precise calculation of the Ameriflex diaphragm stresses
SKU: n/a
Amerigear Couplings
Amerigear® Class I Gear
Amerigear Class I High Performance Gear couplings with fully crowned gear teeth are designed for higher torque, higher speed, and higher misalignment to accommodate the increased performance demands of modern, rotating equipment. Standard and custom designs are manufactured to precision tolerances to meet weight, size, temperature, speed and misalignment requirements. Higher torque, higher speed, and higher misalignment requirements; this is the trend in rotating mechanical equipment. Let Ameridrives Couplings, first to apply the Fully Crowned Tooth concept to a gear-type coupling in the early 1950’s, supply a coupling for your needs. Our engineering know-how in tooth design, material and lube selection, and manufacturing techniques stands ready to serve you. We can supply you with one of our conventional Class I high performance designs, or let us custom-design a coupling for your application.
SKU: n/a
Amerigear Couplings
Amerigear® Gear Couplings
Amerigear®.., the first, the finest… flexible coupling with Fully-Crowned Gear Teeth. In contrast with ordinary gear tooth forms, the Amerigear Fully-Crowned Tooth represents the ultimate achievement in the art of gear tooth design, wherein all three working portions of the tooth are crowned.
As a result, the teeth act much like a rocking chair, capable of sliding freely in the axial direction without digging or gouging the internal mating teeth. Because of this design advantage, Amerigear Flexible Couplings with Fully-Crowned Gear Teeth offer operational benefits of maximum load-carrying capacity with minimum size, maximum reliability and long life.
SKU: n/a
Amerigear Couplings
Amerigear® Gear Couplings Metal Labyrinth Seal
Metal Labyrinth Seal
The FAST’S© Coupling was the standard in the metals industry for decades. Ameridrives now offers the labyrinth/metal ring seal option for your coupling needs. This coupling is a part for part “Drop-In” replacement for the FAST’S© coupling.
Labyrinth Seal Gear Couplings
Ameridrives Couplings has introduced a new product, a component part-for-part “drop-in” replacement for FAST’S® coupling.
“Drop-In” Replacement for FAST Coupling | |||
| FAST | Amerigear | FAST | Amerigear |
| 1-1/2 | 1-1/2 | 4-1/2 | 4-1/2 |
| 2-1/2 | 2-1/2 | 5-1/2 | 5-1/2 |
| 3 | 3 | 6 | 6 |
| 3-1/2 | 3-1/2 | 7 | 7 |
| 4 | 4 | ||
SKU: n/a
Amerigear Mill Spindles
Amerigear® SL and SF Mill Spindles
SL Series (Leveler type) and SF Series (Flange type) spindles are designed for medium torque mill applications and auxiliary equipment where high misalignment capacity is required and where equipment must be disconnected quickly and/or frequently. Some of the advanced design technology incorporated into more expensive type spindles are made available in these series. Typical applications include drives for auxiliary equipment such as levelers, uncoilers, side trimmers, tension, runout tables, pinch rolls, brush rolls, bridles, flatteners, and scale breakers. SL Spindles can also be used on applications where shaft center-to-center spacing is minimal and where diameters are limited.
SKU: n/a
Amerigear Mill Spindles
Amerigear® SM Mill Spindles
SM Series spindles are custom-designed and used primarily on rolling mill drives ranging from heavy duty, hot reversing roughers to high speed cold mills. The spindles used on these drives are often limited by the minimum roll size,and they must handle high continuous loads. These spindles must also accommodate high misalignment angles due to the constant change in material thickness, roll size, and roll change requirements.
Advanced Gear Design enables Ameridrives to optimize mill spindles for the specific operating conditions. The high angle, largely loaded steel mills benefit with less maintenance, lower cost, increased productivity and minimal failures.
SKU: n/a
Disc Couplings
Torsi-Lock Hubs
Torsi-Lock provides the ease of a slip fit with the power of a shrink fit.
Ameridrives Couplings has responded to industry demand for a cold-install hub that provides the secure torque transmission and balance repeatability of an interference fit. We’ve combined our Ameriloc shaft locking devices with Torsiflex-i to provide a pre-engineered solution that meets the balance requirements of API 610.
SKU: n/a
Disc Couplings
Torsiflex-I Disc Couplings
Torsiflex-i disc couplings are specifically designed for process pump and general industrial applications. Torsiflex is an all-metal disc coupling requiring no lubrication which incorporates a plug-in feature to allow installation and removal without disturbing the pump alignment.
Advantages
Standard coupling is fully compliant with the requirements of API 610 / ISO 14691
Plug-in spacer design allows installation and removal without disturbing the hubs
Inch series hub attachment screws (Metric available upon request)
Robust disc pack design allows for greater torque load in a smaller coupling, resulting in lower weight
Large bolts for high clamp load, increasing frictional torque load, and reduced bolt bending stress
Max bores matched to NEMA motor shafts, resulting in up to 60% weight savings per application
Smaller diameter and lower weight per HP provide better inherent balance
ATEX compliance is standard — Exll 2GDc135degC(T4)
Built-in Anti-Flail Feature
Zinc Phosphate coating standard
Large hubs available on first two sizes
Compliance with API 671 / ISO 10441 is available
SKU: n/a
Disc Couplings
Turboflex Plus High Performance Disc Couplings
Two leading international flexible coupling manufacturers, Ameridrives® International and Bibby Turboflex introduce a new series of high performance disc couplings designed to meet the stringent requirements of today’s turbomachinery market.
The Turboflex Plus combines the proven Turboflex and Ameridisc disc couplings together with the experience of the Ameriflex diaphragm producing a coupling as ideally suited to sensitive high speed turbocompressors as it is to low speed load couplings whilst offering an economical solution and being fully compliant API-671/ISO10441 for critical oil and gas, energy, and petrochemical applications. Altra Couplings are selected where quality and reliability are essential to the operation of a plant.
SKU: n/a
Amerigear Couplings
Amerigear® Class I Gear
Amerigear Class I High Performance Gear couplings with fully crowned gear teeth are designed for higher torque, higher speed, and higher misalignment to accommodate the increased performance demands of modern, rotating equipment. Standard and custom designs are manufactured to precision tolerances to meet weight, size, temperature, speed and misalignment requirements. Higher torque, higher speed, and higher misalignment requirements; this is the trend in rotating mechanical equipment. Let Ameridrives Couplings, first to apply the Fully Crowned Tooth concept to a gear-type coupling in the early 1950’s, supply a coupling for your needs. Our engineering know-how in tooth design, material and lube selection, and manufacturing techniques stands ready to serve you. We can supply you with one of our conventional Class I high performance designs, or let us custom-design a coupling for your application.
SKU: n/a
Amerigear Couplings
Amerigear® Gear Couplings
Amerigear®.., the first, the finest… flexible coupling with Fully-Crowned Gear Teeth. In contrast with ordinary gear tooth forms, the Amerigear Fully-Crowned Tooth represents the ultimate achievement in the art of gear tooth design, wherein all three working portions of the tooth are crowned.
As a result, the teeth act much like a rocking chair, capable of sliding freely in the axial direction without digging or gouging the internal mating teeth. Because of this design advantage, Amerigear Flexible Couplings with Fully-Crowned Gear Teeth offer operational benefits of maximum load-carrying capacity with minimum size, maximum reliability and long life.
SKU: n/a
Amerigear Couplings
Amerigear® Gear Couplings Metal Labyrinth Seal
Metal Labyrinth Seal
The FAST’S© Coupling was the standard in the metals industry for decades. Ameridrives now offers the labyrinth/metal ring seal option for your coupling needs. This coupling is a part for part “Drop-In” replacement for the FAST’S© coupling.
Labyrinth Seal Gear Couplings
Ameridrives Couplings has introduced a new product, a component part-for-part “drop-in” replacement for FAST’S® coupling.
“Drop-In” Replacement for FAST Coupling | |||
| FAST | Amerigear | FAST | Amerigear |
| 1-1/2 | 1-1/2 | 4-1/2 | 4-1/2 |
| 2-1/2 | 2-1/2 | 5-1/2 | 5-1/2 |
| 3 | 3 | 6 | 6 |
| 3-1/2 | 3-1/2 | 7 | 7 |
| 4 | 4 | ||
SKU: n/a
Amerigear Mill Spindles
Amerigear® SL and SF Mill Spindles
SL Series (Leveler type) and SF Series (Flange type) spindles are designed for medium torque mill applications and auxiliary equipment where high misalignment capacity is required and where equipment must be disconnected quickly and/or frequently. Some of the advanced design technology incorporated into more expensive type spindles are made available in these series. Typical applications include drives for auxiliary equipment such as levelers, uncoilers, side trimmers, tension, runout tables, pinch rolls, brush rolls, bridles, flatteners, and scale breakers. SL Spindles can also be used on applications where shaft center-to-center spacing is minimal and where diameters are limited.
SKU: n/a
Amerigear Mill Spindles
Amerigear® SM Mill Spindles
SM Series spindles are custom-designed and used primarily on rolling mill drives ranging from heavy duty, hot reversing roughers to high speed cold mills. The spindles used on these drives are often limited by the minimum roll size,and they must handle high continuous loads. These spindles must also accommodate high misalignment angles due to the constant change in material thickness, roll size, and roll change requirements.
Advanced Gear Design enables Ameridrives to optimize mill spindles for the specific operating conditions. The high angle, largely loaded steel mills benefit with less maintenance, lower cost, increased productivity and minimal failures.
SKU: n/a
Diaphragm Couplings
Ameriflex® Diaphragm Couplings
Since its introduction in 1971, the Ameriflex multiple convoluted diaphragm coupling has continued to set new standards for life and reliability in high performance machinery applications. Today, by using the latest design and manufacturing technology, Ameridrives Couplings is able to offer increased diaphragm coupling performance without compromising this outstanding reliability.
Advanced analysis and manufacturing processes have produced increased ratings without reducing safety factors. The use of the latest finite element analysis methods verified by strain gage and dynamic testing has allowed for a more precise calculation of the Ameriflex diaphragm stresses
SKU: n/a
Disc Couplings
Torsi-Lock Hubs
Torsi-Lock provides the ease of a slip fit with the power of a shrink fit.
Ameridrives Couplings has responded to industry demand for a cold-install hub that provides the secure torque transmission and balance repeatability of an interference fit. We’ve combined our Ameriloc shaft locking devices with Torsiflex-i to provide a pre-engineered solution that meets the balance requirements of API 610.
SKU: n/a
Disc Couplings
Torsiflex-I Disc Couplings
Torsiflex-i disc couplings are specifically designed for process pump and general industrial applications. Torsiflex is an all-metal disc coupling requiring no lubrication which incorporates a plug-in feature to allow installation and removal without disturbing the pump alignment.
Advantages
Standard coupling is fully compliant with the requirements of API 610 / ISO 14691
Plug-in spacer design allows installation and removal without disturbing the hubs
Inch series hub attachment screws (Metric available upon request)
Robust disc pack design allows for greater torque load in a smaller coupling, resulting in lower weight
Large bolts for high clamp load, increasing frictional torque load, and reduced bolt bending stress
Max bores matched to NEMA motor shafts, resulting in up to 60% weight savings per application
Smaller diameter and lower weight per HP provide better inherent balance
ATEX compliance is standard — Exll 2GDc135degC(T4)
Built-in Anti-Flail Feature
Zinc Phosphate coating standard
Large hubs available on first two sizes
Compliance with API 671 / ISO 10441 is available
SKU: n/a
Disc Couplings
Turboflex Plus High Performance Disc Couplings
Two leading international flexible coupling manufacturers, Ameridrives® International and Bibby Turboflex introduce a new series of high performance disc couplings designed to meet the stringent requirements of today’s turbomachinery market.
The Turboflex Plus combines the proven Turboflex and Ameridisc disc couplings together with the experience of the Ameriflex diaphragm producing a coupling as ideally suited to sensitive high speed turbocompressors as it is to low speed load couplings whilst offering an economical solution and being fully compliant API-671/ISO10441 for critical oil and gas, energy, and petrochemical applications. Altra Couplings are selected where quality and reliability are essential to the operation of a plant.
SKU: n/a
Universal Joints
Americardan 2000 Series U Joints
The Ameridrives Universal Joint is available in seven basic bearing designs:
Sizes U2131-U2155: Needle bearing design. Bearing caps are retained by snap rings.
Sizes U2160-U2188: Needle bearing design. Bearing caps are retained by bolts.
Sizes U2192: Uses two rows of roller bearings. Bearing caps are retained by snap rings. Lube fitting in center of cross.
SKU: n/a
Universal Joints
Americardan 5000 and 3000 Series U-Joints
Designed for operation at high misalignment angles up to 15º. Bearing and seal design resists lubrication loss and contamination. Ideal for use in severe atmospheric conditions. Superior materials and tight tolerances have proven to reduce vibration levels in rolling mills.
5000 Series are high torque designs ideal for applications with diameter restrictions such as cold mills. Catalog sizes range from 225 mm to 860 mm swing diameters and peak torque capacities up to 5647 kNm. Higher torque, custom designs are available in excess of 1200 mm swing diameter.
3000 Series are rated for high misalignment angles and are available in catalog sizes from 55 mm to 860 mm swing diameters and peak torque capacities up to 3153 kNm. Higher torque, custom designs are available in excess of 1000 mm swing diameter. Sizes 3440 and larger incorporate a unique inner race design within the bearing package to reduce routine repair costs by approximately 50%.
SKU: n/a
Universal Joints
Americardan J Series Universal Joints
Model J Series U-joints use only high-wing bearing cap design. Developed for operation misalignment at high angles up to 15º. Bearing and seal design resists lubrication loss and contamination. Ideal for use in severe atmospheric conditions.
SKU: n/a
Product Carousel Tabs
Power Transmission Products
Bevel Gear Box (FG and FGH )
For 14000 & 30,000 lbs, Housing is made of closed grain cast-iron, for higher sizes, SG 500/7 material.
Screw made of Cr-Mo medium Carbon Steel, hardened and tempered for high core strength.
Nut made of aluminum bronze to British Standard grade AB2.
Bevel Gears Case hardened.
Tapered roller bearings to carry heavy axial as well as radial loads.
SKU: n/a
Motion Technology Products
CWJ worm gear screw jack
Worm Shaft Case carburized Steel, hardened and ground thread profile.
Trapezoidal Screw Shaft Cr-Mo Steel, hardened & tempered.
Housing Alloy aluminum for 5 and 10 kN, all higher sizes in SG Iron.
Worm Wheel and travelling nut in Aluminium Bronze.
SKU: n/a
Motion Technology Products
Electric Cylinder (ECL Series)
Worm Shaft Case carburized Steel, hardened and ground thread profile
Trapezoidal Screw Shaft Cr-Mo Steel, hardened & tempered
Housing Alloy aluminum for 5 and 10 kN, all higher sizes in SG Iron
Worm Wheel and travelling nut in Aluminium Bronze
SKU: n/a
Motion Technology Products
MWJ Screw Jacks (Metric series)
CLASSIC Model MWJ.
15 Different Sizes.
Lifting Capacities 5kN TO 1500kN.
Drive Motor Speed up to 1500 rpm.
Self Locking Trapezoidal Screw.
Worm Gear in two ratios, Nominal and Slow.
Top and Bottom Guide bushes for Lifting Screw.
Worm Wheel hobbed for optimum blue contact.
Filled with NLGI EP 1 or 2 grade grease.
SKU: n/a
Power Transmission Products
Phase shifter
Applications of Phase Shifting
Printing Machine
Packaging machines
Weaving Machines
Paper making plant
Paper Processing plant
In practical application one can distinguish three possibilities
Adjustment operation Speed superimposition
This refers to the change of the output rotation over a longer period of time
Emergency operation
Incase the main drive fails , a limited amount of movement of the output shaft can be achieved through driving the worm shaft
SKU: n/a
Product Carousel Tabs
Product Carousel Tabs
Motor
Motovario electric motors
Motovario three phase brake motors are the most effective and economical solution for transmissions requirements in alternating current. The three-phase motors are available as per IEC international standards from size 063 to 280 in versions with B5 and B14 flanges and B3 feet. They are available with single polarity (2, 4, 6; IE2 efficiency from size 080, IE3 from size 132) and with alternating or direct current brake and a power range from 0.09 kW to 90 kW.
Certifications Available for TS/TH: ATEX 3GD – UL/CSA/EAC
Certifications Available for TBS/TBH: UL/CSA/EAC
SKU: n/a
Gear Reducer
Motovario helical gear reducers
Designed to offer maximum reliability even in the harshest operating conditions, the Motovario helical gear reducers – H series guarantees complete versatility and is suitable for applications that require high radial loads.
The H-series includes a large number of extremely versatile models, in cast iron (sizes 030 to 140).
Certifications Available: ATEX 2GD/3GD
Warranty: Two years from date of delivery.
SKU: n/a
Motor
Motovario mid heavy duty gearboxes
The Motovario mid heavy duty gearboxes PBZ series consists of parallel helical and bevel-helical gear reducers up to 4 reduction stages, characterised by high power density, compact size, modularity, reliability and a favourable performance/sturdiness ratio.
SKU: n/a
Gear Reducer
Motovario shaft mounted gear reducers
Specifically designed for applications involving conveyors or augers, these units are also suitable for a wide variety of industrial fields.
The S series Motovario shaft mounted gear reducers, available in cast iron from size 050 to 125, offer a wide range of reduction ratios, ensuring maximum efficiency in all operating conditions.
The new S Series includes two new sizes, 140 and 150, to extend the shaft mounting to heavier applications.
Certifications Available (up to size 125): ATEX 2GD/3GD
SKU: n/a
Gear Reducer
Motovario worm gear reducers
NMRV and NMRV POWER Motovario worm gear reducers currently represent the most advanced solution to market requirements in terms of efficiency and flexibility.
The new NMRV Power series, also available as compact integral helical/worm option, has been designed with a view to modularity: low number of basic models can be applied to a wide range of power ratings guaranteeing top performance and reduction ratios from 5 to 1000.
SKU: n/a
Product Carousel Tabs
Drum Brakes
AIR DISC BRAKES HS-CODE 87169090
QP mouth, CQP mouth series pneumatic clamp disc brakes, are widely used in the small and medium-sized drive mechanism to stop or deceleration. Tension brake winding institutions, such as paper tension, tension control of the press printing newsprint, steel plate (steel wire) unwound tension wire and cable actinomycetes, put the cable tension control….
SKU: n/a
Drum Brakes
Electro Hydraulic Disc Brake YPZ2-560II/ Bed 121/6-L-K1K2
We are manufacturer to produce drum brake, disc brake, electro hydraulic thruster, which can be used for lifting, metallurgy, mining, ports, construction etc. All of our brakes and thrusters are apprroved by ISO9001, and we provide 18 month quality warranty….
SKU: n/a
Drum Brakes
Mill Duty Thruster Brake (Manufacturer Of Electro Hydraulic Thruster Brake)
Henan Zhongyuan Brake Co., Ltd is the leading manufacturer of Electro hydraulic Thruster Brake. Our mill duty Thruster Brakes are suitable for 400/440 Volts, 3 Phase A.C. supply for a wide range of drum sizes, from 100mm to 800 mm dia. Higher sizes can also be supplied against specific requirements. The brake is applied by the tension of the compressed springs mounted vertically between the thruster and brake lever. The thruster rods are connected with the brake by means of an angle lever. As the piston travels upwards the angle lever turns, pushes the brake rod and compresses the brake spring. Simultaneously, the brake lever on the other side of the wheel (Brake Drum) is retracted….
SKU: n/a
Drum Brakes
QP Series Disc Brake Caliper/ZYBC China Disc Brake Manufacturer
QP、CQP series Pneumatic Disc Brakes are widely used for speed reducing ,stopping/braking of the low or medium torque driving mechanism. The brakes can also be applied as tension brake on winding machines, such as: paper-web tension control, news paper publishing tension control,steel unwind control, wire and cable reel unwind tension etc….
SKU: n/a
Drum Brakes
YP3 Series Crane Disc Brake
YP Series Electro-hydraulic Disc Brakes are advanced products with high performance and multiple functions. They are maintenance-friendly due to advanced functions applied on them such as automatic shoe clearance balancing and wear-self-compensation device. Various limit switches can provide interlocking protection signal to main machinery PLC. They fit very well for decelerating and stop/braking large-scale modern machines such as loading and unloading machinery, lifting and transporting machinery, metallurgy equipment and mining equipment….
SKU: n/a
Product Carousel Tabs
Motor
AC Motor DRK
The DRK.. motor in the modular DR.. series motor system is a single-phase motor that can be operated on a single-phase power supply (instead of the usual three-phase power supply). The DRK.. motor comes equipped with running capacitor CB.
DRK.. series motors can be operated on the following single-phase power grids:
– 220 V/ 50 Hz, 230 V / 50 Hz, 220 V / 60 Hz or 230 V / 60 Hz
The running capacitor integrated in the terminal box allows for operation under many demanding ambient conditions. SEW-EURODRIVE also offers ET56 and ER63 motors.
SKU: n/a
Motor
AC Motor DT/DV Series
DT / DV series AC motors and AC brake motors are the ideal match for SEW-EURODRIVE vertical gear units. Our wide range of variants ensures that we have the right motor for your application, whether 2-, 4-, 6- or 8-pole or multi-speed. SEW-EURODRIVE brake motors have integrated DC safety disc brakes. The brake control is installed in the terminal box as standard, but is also available in control cabinet version as an option. The patented two-coil brake system facilitates high starting frequency and positioning accuracy with particularly short response and reaction times.
SKU: n/a
Motor
Aseptic Drives DAS Series
Solutions for use in dry hygiene areas:
DAS series aseptic gearmotors for drive solutions with smooth surfaces and without fans:
Motors in degree of protection IP66 (brakemotors IP65)
Motor corrosion protection: KS internal coating
Surface protection OS1 to OS4
Motor protection thermistor in thermal class F, TH optional (thermocontact)
IS plug connector
SKU: n/a
Geared Motor
Gearmotor R series (two-stage and three-stage)
Our complete range of helical gearmotors provides the optimum size and power solution for every drive task. And for applications where weight is an issue, our multi-stage gear units provide something special: Thanks to their die-cast aluminum design, the models R07, R17 and R27 are three particularly efficient lightweights – ideal as satellite drives and for use in light machine constructions. Reduced backlash helical gear units are also available for particularly precise requirements.
SKU: n/a
Geared Motor
Helical Gearmotor RM Series
RM gearmotors with extended output bearing hub are a special type of helical gearmotor. They were designed especially for agitating applications and allow for high overhung and axial loads and bending moments. The remaining data corresponds to that of standard helical gearmotors.
SKU: n/a
Motor
Servo Gearmotors
System solutions with servo gearmotors: helical gear units, parallel shaft helical gear units, helical-bevel gear units and helical-worm gear units can be mounted on SEW-EURODRIVE’s synchronous servomotors DS, CM and CMP servomotors.
The /R option (reduction of circumferential backlash combined with high efficiency and high-endurance gearing) gives the gear units servo-typical characteristics, such as high positioning accuracy. With their wide range of options, the MOVIDRIVE® drive inverters provide you with the functional, scalable and intelligent systems you need.
SKU: n/a
Product Carousel Tabs
Motor
Siemens electric motors
Don’t compromise when selecting your low voltage motor. Choose a Siemens AC motor right from the start. We are the leading drive technology manufacturer for industrial applications. As your partner, we offer you the best AC motor systems — at a convincing price/performance ratio and backed by our global support network for production, sales, and service.
SKU: n/a
Geared Motor
SIMOGEAR
Having market conform connecting dimensions, the latest SIMOGEAR gear motors are 1:1 compatible to the current standard. SIMOGEAR gear motors are an economic alternative easy for replacements in already existing installations or to implement in new designs. Surely, the new series of gear motors fit the Siemens DriveTrain in an optimal way.
The new SIMOGEAR Siemens geared motors deliver performance from 0.09 kW up to 55 kW. It can achieve a gear unit torque up to 8.000 Nm with helical, parallel shaft, helical bevel and worm geared gear units, additional types and sizes will follow. Due to accordance to the current measures, SIMOGEAR is compatible to many other suppliers of gear motors.
SKU: n/a
Pressure Transmitter
SITRANS P DS III
The SITRANS P DS III series includes digital pressure transmitters for measuring gauge pressure, absolute pressure, differential pressure, flow and level. Even the standard devices offer comprehensive diagnostics and simulation functions with high reliability.
SKU: n/a
Pressure Transmitter
SITRANS P280
Broad range of applications by various pressure ranges available (1.6, 10, 50, 200, 320 bar; 23, 145, 725, 2900, 4641 psi).
Easy usability by LCD display with functional display items and icons and three push buttons for maximum efficiency for setup, diagnostics, communication and security settings with no additional devices or tools
Maintenance-friendly handling by 90 and 180 degree turnable display and backlight function
Sleep mode for efficient battery life management
Battery status display on LCD and in network overview
SKU: n/a
Pressure Transmitter
SITRANS P300
With hygiene (EHEDG, 3A), material and calibration certificates eminently suited to the food and beverage and pharmaceutical industry
Especially suitable for degrees of protection to IP68 and IP69K, CIP/SIP cleaning, and highly viscos measuring media
Broad application opportunities by measurement cells for gauge and absolute pressure
SKU: n/a
Pressure Transmitter
SITRANS P310
The SITRANS P310 is a digital pressure transmitter with integrated HART diagnostic functions and a high operating comfort. Representing a basic device for easy measurements with low accuracy requirements the P310 complements the already existing P DS III. The different design variants for measuring gauge and differential pressure are available.
SKU: n/a
Pressure Transmitter
SITRANS P410
The SITRANS P410 is a digital pressure transmitter with integrated diagnostic functions. It complements the existing P DS III as a “high performance” version with increased measuring accuracy of 0.04 % and offers different design variants for measuring gauge and differential pressure.
SKU: n/a
Pressure Transmitter
SITRANS P500
Improved control of your systems due to extremely short step response time.
Direct-connected use in process temperatures of up to 125 °C (257 °F) even without a remote seal system.
High degree of user-friendliness via a full-text-enabled, backlit display and 3 pushbuttons. The transmitter can also be configured and operated conveniently from the control system using the HART protocol.
SKU: n/a
Product Carousel Tabs
Product Carousel Tabs
Seals
HIGH PRESSURE OIL SEALS
The rotary shaft oil seal is an indispensable component in lubricated rotating equipment and must be chosen with caution in order to ensure that the correct design and materials are used to provide a long-lasting life for the rotating equipment.
These variations of the G and M type seals are engineered to withstand pressure up to 10 BAR (1 MPa), although this limit has been exceeded in some applications. These seals are available with or without an additional dust lip. The G type and its high pressure variants show a metal insert covered by rubber, while the M type and its variants offer a bare metal body on the outside diameter.
SKU: n/a
Seals
OIL FILM BEARINGS
Primary shaft oil seals for oil film bearings. The BBS® oil seals are available in both DF and MX style to fit every customers’ requirement.
Used in steel mill: back-up rolls (hot and cold rolling mills). The BBS® oil seals can be supplied together with the corresponding Water Seal, or with specific V-Rings (secondary seal).
SKU: n/a
Seals
ROTARY SHAFT OIL SEAL
The rotary shaft oil seal is an indispensable component in any lubricated rotating equipment.
The •FP• oil seals provide the right solution to every sealing problem.
•FP• rotary shaft oil seals are produced according to modern engineering techniques with high-performing materials, as requested by industry specifications.
SKU: n/a
Seals
V-RINGS
Endless all-rubber face seal produced up to 2.100 mm in one single piece and joint-vulcanized for larger diameters. It works as a front seal and it is the perfect solution to prevent contamination from dirt, dust, or water. It can be used as a secondary seal to protect the primary seals.
The V-Ring is a seal of easy use and assembly since it is self-retaining on the shaft and does not need a special finishing grade and tolerance. The contact area can have a roughness from Ra 0.5 to Ra 1.6 according to the speed and the fluids to be sealed.
SKU: n/a
Seals
WIPER SEALS
Rod wipers for alternative linear movements have been designed to give first-class protection to seals and driving bodies in hydraulic and pneumatic cylinder applications.
The main function of the rod wiper is to keep the rod clean from any possible impurity.
The •FP• rod wipers have a chamfer on the outside diameter to facilitate the press fitting into the housing. To simplify the installation, the bore should have a chamfer as per DIN 3760.
SKU: n/a
Product Carousel Tabs
Pumps
Diaphragm Pumps
Parker miniature diaphragm pump solutions provides the highest flow per watt available on the market today. Suitable for a broad range of diaphragm pump applications, our miniature pumps promise significant cost savings and reduced field service time thanks to a unique design and advanced motor technology. We also offer a full line of miniature liquid diaphragm pumps that harness the higher fluidic resistance of liquids to deliver higher levels of performance across a wide range of applications.
SKU: n/a
Product Carousel Tabs
Butterfly Valve
Butterfly valve type 567 PVC-C Bare shaft
Butterfly valves type 567/568 are compact, flexible and reliable shut-off valves for wafer and lugstyle applications.
Our system’s modular design principle allows you to exchange individual system components – fast, easily and at very little expense and effort.
Type 567 butterfly valves are now available in dimensions up to DN600/24″ in PP-H and PVC-U (up to DN400/16″).
Model:
Overall length according to EN 558, ISO 5752
Connecting dimension: ISO 7005 PN 10, EN 1092 PN 10, DIN 2501 PN 10, ANSI/ASME B 16.5 Class 150, BS 1560: 1989, BS 4504, JIS B 2220
Interface F07 according to DIN/ISO 5211
SKU: n/a
Butterfly Valve
Butterfly valve type 567 PVC-C Hand lever with ratchet settings
Butterfly valves type 567/568 are compact, flexible and reliable shut-off valves for wafer and lugstyle applications.
Our system’s modular design principle allows you to exchange individual system components – fast, easily and at very little expense and effort.
Type 567 butterfly valves are now available in dimensions up to DN600/24″ in PP-H and PVC-U (up to DN400/16″).
Model:
Overall length according to EN 558, ISO 5752
Connecting dimension: ISO 7005 PN 10, EN 1092 PN 10, DIN 2501 PN 10, ANSI/ASME B 16.5 Class 150, BS 1560: 1989, BS 4504, JIS B 2220
SKU: n/a
Butterfly Valve
Butterfly valve type 567 PVC-C Reduction gear with handwheel
Butterfly valves type 567/568 are compact, flexible and reliable shut-off valves for wafer and lugstyle applications.
Our system’s modular design principle allows you to exchange individual system components – fast, easily and at very little expense and effort.
Type 567 butterfly valves are now available in dimensions up to DN600/24″ in PP-H and PVC-U (up to DN400/16″).
Model:
Overall length according to EN 558, ISO 5752
Connecting dimension: ISO 7005 PN 10, EN 1092 PN 10, DIN 2501 PN 10, ANSI/ASME B 16.5 Class 150, BS 1560: 1989, BS 4504, JIS B 2220
SKU: n/a
Butterfly Valve
Metal – butterfly valve type 038G Reduction gear with handwheel Disc: stainless steel
Butterfly Valve
Metal – butterfly valve type 038G Reduction gear with handwheel Disc: stainless steel
Model:
Lug Style
Body GGG40 (A 395 / A395 M-99, EN-JIS 1020 EN1563) Rilsan® coating
Body from DN350 Epoxy® coating
Installation length: EN 558 row 20
Interface according to DIN EN ISO 5211
Pressure range: 16 bar (DN 50-300); 10 bar (DN 350-600)
Single-piece axis with square profile, up to DN 600 mm 2-pieces axis
Multiple flange connection: DIN PN 6/10/16; other standard e.g. ANSI/ASME B16.5 Class 150 on request
Option:
Electric and pneumatic actuator on request
Other liner material on request
SKU: n/a
Product Carousel Tabs
Cable Chain
STEEL CABLE CHAIN
SHINSUNG drag chains are used where energy has to be supplied to mobile machine parts or apparatus.
The chain joint lock in the opposite direction.
In SHINSUNG drag chains, cables and hoses conveying varying substances can be carried alongside one another at the same time.
SKU: n/a
Product Carousel Tabs
Product Carousel Tabs
Spring và Shock Obsober
Stainless Steel Compression Spring
Stainless Steel Compression Spring
1:Wire diameters from 0.05 to 18mm
2:Outside diameters either constant, tapered, convex or concave
3:Springs can have loading characteristics that are either constant or variable
4:We are specialists in precision end grinding to ensure accurate seating in your spring application.
1:Wire diameters from 0.05 to 18mm
2:Outside diameters either constant, tapered, convex or concave
3:Springs can have loading characteristics that are either constant or variable
4:We are specialists in precision end grinding to ensure accurate seating in your spring application.
Brand: MingLi
Item NO.: MLC-1
Payment: T/T,L/C
Product Origin: Ningbo China
Color: Custom color
Shipping Port: NingBo
Lead Time: 5-15 Days
SKU: n/a
Spring và Shock Obsober
Stainless Steel Extension Spring
Stainless Steel Extension Spring
Wire size from 0.05mm to 16mm
End types available are machine, swivel, crossover and extended hook designs
Winamac Coil Spring specializes in custom hook configurations fabricated to individual customer requirements
Brand: MingLi
Item NO.: MLE-1
Payment: T/T,L/C
Product Origin: Ningbo China
Color: Custom color
Shipping Port: NingBo
Lead Time: 5-15 Days
SKU: n/a
Spring và Shock Obsober
Stainless Steel Torsion Spring
Stainless Steel Torsion Spring
Wire sizes from 0.05mm to 16mm
Wide variety of leg lengths, shapes, anchoring configurations and coil diameters.
In-house shot peening available to improve fatigue life of your spring.
Brand: MingLi
Item NO.: MLT-1
Payment: T/T,L/C
Product Origin: Ningbo China
Color: Custom color
Shipping Port: NingBo
Lead Time: 5-15 Days
SKU: n/a
Spring và Shock Obsober
Stainless Steel Wire Forming Spring
Stainless Steel Wire Forming Spring
Wire Forms products are widely used in automobile, electrical, mechanical, optical, medical, daily chemical products, sports equipment and other induitrses，Enterprise sprise spirit, humanistic quality.
Brand: MingLi
Item NO.: MLF-1
Payment: T/T,L/C
Product Origin: Ningbo China
Color: Custom color
Shipping Port: NingBo
Lead Time: 5-15 Days
SKU: n/a
Spring và Shock Obsober
TB Brown Standard Die Springs
TB Brown Standard Die Springs
Our company can produce OD from 6mm-60mm JIS and ISO die spring.
Company’s annual production capacity is about 10 million pcs.
We have warehouse over 1200 squire meters area.
Metrial: 65Mn and Alloy Steel.
Brand: MingLi
Item NO.: MLTB-1
Payment: T/T,L/C
Product Origin: Ningbo China
Color: Brown
Shipping Port: NingBo
Lead Time: 5-15 Days
SKU: n/a
Spring và Shock Obsober
TF Yellow Standard Die Springs
TF Yellow Standard Die Springs
Our company can produce OD from 6mm-60mm JIS and ISO die spring.
Company’s annual production capacity is about 10 million pcs.
We have warehouse over 1200 squire meters area.
Metrial: 65Mn and Alloy Steel.
Brand: MingLi
Item NO.: MLTF-1
Payment: T/T,L/C
Product Origin: Ningbo China
Color: Yellow
Shipping Port: NingBo
Lead Time: 5-15 Days
SKU: n/a
Spring và Shock Obsober
TH Green Standard Die Springs
TH Green Standard Die Springs
Our company can produce OD from 6mm-60mm JIS and ISO die spring.
Company’s annual production capacity is about 10 million pcs.
We have warehouse over 1200 squire meters area.
Metrial: 65Mn and Alloy Steel.
Brand: MingLi
Item NO.: MLTH-1
Payment: T/T,L/C
Product Origin: Ningbo China
Color: Green
Shipping Port: NingBo
Lead Time: 5-15 Days
SKU: n/a
Spring và Shock Obsober
TL Blue Standard Die Springs
TL Blue Standard Die Springs
Our company can produce OD from 6mm-60mm JIS and ISO die spring.
Company’s annual production capacity is about 10 million pcs.
We have warehouse over 1200 squire meters area.
Metrial: 65Mn and Alloy Steel.
Brand: MingLi
Item NO.: MLTL-1
Payment: T/T,L/C
Product Origin: Ningbo China
Color: Blue
Shipping Port: NingBo
Lead Time: 5-15 Days
SKU: n/a
Spring và Shock Obsober
TM Red Medium Standard Die Springs
TM Red Medium Standard Die Springs
Our company can produce OD from 6mm-60mm JIS and ISO die spring.
Company’s annual production capacity is about 10 million pcs.
We have warehouse over 1200 squire meters area.
Metrial: 65Mn and Alloy Steel.
Brand: MingLi
Item NO.: MLTM-1
Payment: T/T,L/C
Product Origin: Ningbo China
Color: Red
Shipping Port: NingBo
Lead Time: 5-15 Days
SKU: n/a
Product Carousel Tabs
Positioners
Electropneumatic positioner APIS
HART protocol
ATEX certificate II 2G Exia IIC T6/T5 Gb
Simple in installation and programming
Possibility of remote assembling of positioner
Low air consumption
Programmable speed of movement of the actuator’s piston rod
Position transmitter
Possibility of manual controlling of position of actuator’s piston rod
SKU: n/a
Level Transmitters
Magnetic level switch ERH-xx-20
Level signalling of the medium having minimum density 0,70 g/cm3. The basic version, mounted from the top, is available with 92x92mm flange connector, head made from aluminium alloy and M20x1,5 cable gland with casing protection degree IP68. Other versions of mechanic or threaded flange connectors according to the ordering code. There is also a possibility of ordering the level swicth with connector according to the requirements, e. g. with flange acc. to DIN or ANSI standard. The level switch can also be ordered in version fully made from acidproof steel, with additional cover protecting the float, made from stainless steel, with additional cover protecting the float, as well as with certified cable of optional length. The level switch has DNV GL Marine approval.
SKU: n/a
Pressure Transmitter
Pressure transmitter PCE-28 PCE-28/EXD
Any range from 0…25 mbar up to 0…1000 bar
4 ÷ 20 mA two-wire or 0 ÷ 10 V output
Intrinsic safety certificate (ATEX, IECEx)
Explosion proof certificate (ATEX, IECEx)
Low-voltage version with ATEX and IECEx certificate (model PC-29A, PC-29B)
Marine certificate – DNV, BV
Communication protocol Modbus RTU
Gold plated diaphragm
SIL 1 certificate
Version with local display
SKU: n/a
Temperature
Rail-mounted smart temperature transmitters type LI-24L and LI-24/Ex
Galvanic insulation (In, out)
Programmable sensor type
Programmable measuring range
Thermoresistance line compensation
Compensation of thermocouple cold junction
Output signal 4…20mA + Hart protocol
Ambient temperature from -25 to +75 °C
Rail mounting system
Autodiagnostic system
Hart protocol
ATEX certificate (LI-24/Ex)
SKU: n/a
Pressure Transmitter
Smart differential pressure transmitter APR-2000 ALW
4…20 mA, 0…20 mA or 0…5 mA output signal + HART protocol
Display with backlight
SIL 2 certificate
Intrinsic safety certificate (ATEX, IECEx)
Explosion proof certificate (ATEX, IECEx)
PED Conformity (97/23/EC)
Programmable zero range, shift, characteristic and damping ratio with local panel keys
Static pressure limit up to 420bar
Accuracy 0,075% (0,05% on request)
Marine certificate – DNV, BV
Gold plated diaphragms
Wetted parts material Hastelloy C276
SKU: n/a
Level Transmitters
Smart differential pressure transmitter APR-2000 ALW
4…20 mA, 0…20 mA or 0…5 mA output signal + HART protocol
Display with backlight
SIL 2 certificate
Intrinsic safety certificate (ATEX, IECEx)
Explosion proof certificate (ATEX, IECEx)
PED Conformity (97/23/EC)
Programmable zero range, shift, characteristic and damping ratio with local panel keys
Static pressure limit up to 420bar
Accuracy 0,075% (0,05% on request)
Marine certificate – DNV, BV
Gold plated diaphragms
Wetted parts material Hastelloy C276
SKU: n/a
Product Carousel Tabs
Pressure Transmitter
Absolute and gauge pressure Cerabar PMC21
Cost-effective pressure transducer with ceramic sensor for measurement in gases or liquids
The Cerabar PMC21 is a very compact pressure transmitter. It features a capacitive, oil-free ceramic sensor and is able to measure absolute or gauge pressure from 100mbar up to 40bar. It is designed to withstand the harsh conditions in the process industry with ingress protection grades up to IP68 and highly abrasion resistant Ceraphire membrane as well as high quality 316L housing. It can be used in most areas as it offers various certifications like hazardous area or marine certificates.
SKU: n/a
Pressure Transmitter
Absolute and gauge pressure Cerabar PMC51
Digital pressure transmitter with oil-free ceramic sensor for measurement in gases or liquids
The Cerabar PMC51 digital pressure transmitter with capacitive, oil-free ceramic measuring cell is typically used in process and hygienic applications for pressure, level, volume or mass measurement in liquids and gases. It guarantees high degree of system safety thanks to vacuum-proof ceramic membrane with integrated breakage detection. Quick Setup with adjustable measuring range allows simple commissioning, reduces costs and saves time. SIL2 according to IEC 61508 / IEC 61511.
SKU: n/a
Pressure Transmitter
Absolute and gauge pressure Cerabar PMC71
Digital pressure transmitter with oil-free ceramic sensor for measurement in gases or liquids
The Cerabar PMC71 digital pressure transmitter with capacitive, oil-free ceramic measuring cell is typically used in the process and hygienic applications for pressure, level, volume or mass measurement in liquids and gases. It guarantees high degree of system safety thanks to vacuum-proof ceramic membrane with integrated breakage detection. Quick Setup with adjustable measuring range allows simple commissioning, reduces costs and saves time. SIL2/3 according to IEC 61508.
SKU: n/a
Pressure Transmitter
Absolute and gauge pressure Cerabar PMP21
Cost-effective pressure transducer with metal sensor for measurement in gases or liquids
The Cerabar PMP21 is a price-attractive and very compact pressure transmitter. It features a piezo-resistive sensor and is able to measure absolute or gauge pressure from 400mbar up to 400bar. The PMP21 is designed to withstand the harsh conditions in the process industry with ingress protection grades up to IP 68 and high quality materials like 316L. It can be used in most areas as it offers various certifications like hazardous area or marine certificates.
SKU: n/a
Pressure Transmitter
Absolute and gauge pressure Cerabar PMP23
Cost-effective pressure transducer with fully welded design for the food & beverage industry
The Cerabar PMP23 is a price-attractive and compact absolute or gauge pressure transmitter. The piezo-resistive measuring cell with flush-mounted 316L diaphragm was designed for applications in the hygienic industry. PMP23 offers various EHEDG and 3-A certified hygienic process connections, materials with FDA conformity, EG1935/2004 conformity, IP69 protection, optional IO-Link and hazardous area certificates. The device can be delivered with customized measuring ranges up to 40bar.
SKU: n/a
Pressure Transmitter
Differential pressure Deltabar PMD55
Differential pressure transmitter with metal sensor for measurement of pressure differences
The Deltabar PMD55 differential pressure transmitter with piezoresistive sensor and welded metallic membrane is typically used in process or environmental applications for continuous measurement of pressure differences in liquids, vapors and gases. Quick Setup with adjustable measuring range allows simple commissioning, reduces costs and saves time. SIL2 according to IEC 61508 / IEC 61511.
SKU: n/a
Pressure Transmitter
Differential pressure Deltabar PMD75
Differential pressure transmitter with metal sensor for measurement of pressure differences
The Deltabar PMD75 differential pressure transmitter with with piezoresistive sensor and welded metallic membrane is used in all industries for continuous measurement in liquids, vapors and gases. The 3-key operation enables simple and reliable commissioning and operation. The integrated HistoROM data module allows easy management of process and device parameters. Designed according to IEC 61508 for use in SIL2/3 safety applications.
SKU: n/a
Pressure Transmitter
Electronic differential pressure Deltabar FMD71
Electronic differential pressure system utilizing two ceramic sensor modules and one transmitter
The electronic dp Deltabar FMD71 is a differential pressure system, used to measure the pressure or level, volume or mass of liquids in pressurized tanks or distillation columns/evaporators. The high pressure sensor (HP) measures the hydrostatic pressure. The low pressure sensor (LP) measures the head pressure. The level is calculated in the transmitter using these two digital values. The electronic dp system eliminates issues of traditional differential pressure measurements.
SKU: n/a
Pressure Transmitter
Electronic differential pressure Deltabar FMD72
Electronic differential pressure system utilizing two metal sensor modules and one transmitter
The electronic dp Deltabar FMD72 is a differential pressure system, used to measure the pressure, level, volume or mass of liquids in pressurized tanks or distillation columns/evaporators. The high pressure sensor (HP) measures the hydrostatic pressure. The low pressure sensor (LP) measures the head pressure. The level is calculated in the transmitter using these two digital values. The electronic dp system eliminates issues of traditional differential pressure measurements.
SKU: n/a
Product Carousel Tabs
Pressure Transmitter
EJA110E Differential Pressure Transmitter
The EJA110E is a high-performance differential pressure transmitter used to measure liquid, gas, or steam pressure. Featuring Yokogawa DPharp sensor technology, the EJA110E delivers measurements accurately, quickly, and reliably.
EJA-E series models in their standard configuration, with the exception of the Fieldbus, PROFIBUS and Low Power types, are certified as complying with SIL 2 safety requirements.
Accuracy: ±0.055% of Span
Stability: ±0.1% of URL per 10 years
Response Time: 90 msec
SKU: n/a
Pressure Transmitter
EJA118E DP Transmitter with Remote Diaphragm Seals
The EJA110E is a high-performance differential pressure transmitter used to measure liquid, gas, or steam pressure. Featuring Yokogawa DPharp sensor technology, the EJA110E delivers measurements accurately, quickly, and reliably.
EJA-E series models in their standard configuration, with the exception of the Fieldbus, PROFIBUS and Low Power types, are certified as complying with SIL 2 safety requirements.
Accuracy: ±0.055% of Span
Stability: ±0.1% of URL per 10 years
Response Time: 90 msec
SKU: n/a
Pressure Transmitter
EJA310E Traditional-mount Absolute Pressure Transmitter
The EJA-E series of transmitters is Yokogawa’s most recent evolution of the DPharp family. Released in 2012, it combines the ruggedness and success of the work-horse EJA-A series with the performance of the thoroughbred EJX-A series to deliver the type of product you have come to expect from Yokogawa.
The EJA310E is our traditional-mount absolute pressure transmitter in the series.
EJA310E standard features include:
± 0.1% Accuracy
± 0.2% Stability for 10 years
90 ms Response Time
Exida and TUV SIL 2/3 Certified
3,600 psia Maximum Over Pressure (MWP)
Local Parameter Setting (LPS)
Available with HART 5/7, 1 to 5 VDC HART 7 (Low Power), FOUNDATION Fieldbus, PROFIBUS PA, or BRAIN communication.
SKU: n/a
Pressure Transmitter
EJA438E Gauge Pressure Transmitter with Remote Diaphragm Seal
The EJA430E is a high-performance gauge pressure transmitter used to measure liquid, gas, or steam pressure. Featuring Yokogawa DPharp sensor technology, the EJA430E delivers measurements accurately, quickly, and reliably.
EJA-E series models in their standard configuration, with the exception of the Fieldbus, PROFIBUS and Low Power types, are certified as complying with SIL 2 safety requirements.
Accuracy: ±0.055% of Span (Optional ±0.04%)
Response Time: 90 msec
Stability: ±0.1% of URL per 10 years
SKU: n/a
Pressure Transmitter
EJA510E In-Line Mount Absolute Pressure Transmitter
The EJA-E series of transmitters is Yokogawa’s most recent evolution of the DPharp family. Released in 2012, it combines the ruggedness and success of the work-horse EJA-A series with the performance of the thoroughbred EJX-A series to deliver the type of product you have come to expect from Yokogawa.
The EJA510E is our in-line mount absolute pressure transmitter in the series.
EJA510E features include:
± 0.055% Accuracy (0.04% Accuracy optional)
± 0.2% Stability per 10 years
90 ms Response Time
Exida and TUV SIL 2/3 Certified
8,700 psia Maximum Over Pressure
Local Parameter Setting (LPS)
Avaialble with HART 5/7, 1 to 5 VDC HART 7 (Low Power), FOUNDATION Fieldbus, PROFIBUS PA, or BRAIN communication.
SKU: n/a
Pressure Transmitter
EJA530E In-Line Mount Gauge Pressure Transmitter
The EJA530E is a high-performance gauge pressure transmitter used to measure liquid, gas, or steam pressure. Featuring Yokogawa DPharp sensor technology, the EJA530E delivers measurements accurately, quickly, and reliably.
EJA-E series models in their standard configuration, with the exception of the Fieldbus, PROFIBUS and Low Power types, are certified as complying with SIL 2 safety requirements.
Accuracy: ±0.055% of Span
Response Time: 90 msec
Stability: ±0.1% of URL per 10 years
SKU: n/a
Pressure Transmitter
EJX110A Differential Pressure Transmitter
The EJX110A is a high-performance differential pressure transmitter used to measure liquid, gas, or steam pressure. Featuring Yokogawa DPharp sensor technology, the EJX110A delivers measurements accurately, quickly, and reliably.
EJX-A series models in their standard configuration, with the exception of the Fieldbus and PROFIBUS types, are certified as complying with SIL 2 safety requirements.
± 0.04% Accuracy (0.025% Accuracy option available)
± 0.1% per 15 years Stability
90 ms Response Time
3,600 psi MWP
Exida and TUV SIL2 / SIL3 Certified
Local Parameter Setting (LPS)
SKU: n/a
Pressure Transmitter
EJX110B Wireless Differential Pressure Transmitter
The high performance wireless differential pressure transmitter EJX110B features a single crystal silicon resonant sensor and are suitable to measure liquid, gas, or steam flow as well as liquid level, density, and pressure. These transmitters transmit not only process variables but also the setting parameters using wireless signal. The transmitters run on internal batteries, and the installation cost can be decreased since hard-wiring is not required. The communication is compliant with ISA100.11a protocol specifications.
SKU: n/a
Pressure Transmitter
EJX118A DP Transmitter with Remote Diaphragm Seals
The EJX-A series is Yokogawa’s premium performance line of DPharp transmitters. Released in 2004, it offers the performance and stability needed in demanding applications. The EJX-A series performance makes it the thoroughbred of the DPharp family of pressure transmitters.
The EJX118A is the Differential Pressure Transmitter with Remote Diaphragm Seals in the series.
EJX118A features include:
± 0.15% Accuracy
200 ms Response Time
Exida and TUV SIL2 / SIL3 Certified
Local Parameter Setting (LPS)
10-segment Signal Charaterizer
Active Capillary Fill Fluid Density Compensation
SKU: n/a
Pressure Transmitter
EJX310A Traditional-mount Absolute Pressure Transmitter
The EJX-A series is Yokogawa’s premium performance line of DPharp transmitters. Released in 2004, it offers the performance and stability needed in demanding applications. The EJX-A series performance makes it a thoroughbred of the DPharp family of pressure transmitters.
The EJX310A is the traditional-mount Absolute Pressure Transmitter in the series.
EJX310A features include:
± 0.075% Accuracy
± 0.2% per 15 years Stability
90 ms Response Time
Exida and TUV SIL 2/3 Certification
LPS (Local Parameter Setting)
SKU: n/a
Pressure Transmitter
EJX430A Traditional-mount Gauge Pressure Transmitter
The EJX430A is a high-performance gauge pressure transmitter used to measure liquid, gas, or steam pressure. Featuring Yokogawa DPharp sensor technology, the EJX430A delivers measurements accurately, quickly, and reliably.
EJX-A series models in their standard configuration, with the exception of the Fieldbus and PROFIBUS types, are certified as complying with SIL 2 safety requirements.
Accuracy: ±0.04% of Span (Optional ±0.025%)
Response Time: 90 msec
Stability: ±0.1% of URL per 15 years
SKU: n/a
Pressure Transmitter
EJX510A In-Line Mount Absolute Pressure Transmitter
The EJX-A series is Yokogawa’s premium performance line of DPharp transmitters. Released in 2004, it offers the performance and stability needed in demanding applications. The EJX-A series performance makes it a thoroughbred of the DPharp family of pressure transmitters.
The EJX510A is the In-Line mount Absolute Pressure Transmitter in the series.
EJX510A features include:
± 0.04% Accuracy
± 0.2% per 15 years Stability
90 ms Response Time
10,800 psig Maximum Over Pressure
Exida and TUV SIL 2/3 Certified
Local Parameter Setting (LPS)
SKU: n/a
Pressure Transmitter
EJX530A In-Line Mount Gauge Pressure Transmitter
The EJX530A is a high-performance gauge pressure transmitter used to measure liquid, gas, or steam pressure. Featuring Yokogawa DPharp sensor technology, the EJX530A delivers measurements accurately, quickly, and reliably.
EJX-A series models in their standard configuration, with the exception of the Fieldbus and PROFIBUS types, are certified as complying with SIL 2 safety requirements.
Accuracy: ± 0.04% of Span
Response Time: 90 msec
Stability: ± 0.1% of URL per 15 years
SKU: n/a
Pressure Transmitter
EJX610A High Performance In-Line Mount Absolute Pressure Transmitter
The EJX-A series is Yokogawa’s premium performance line of DPharp transmitters. Released in 2004, it offers the performance and stability needed in demanding applications. The EJX-A series performance makes it the thoroughbred of the DPharp family of pressure transmitters.
The EJX610A is the high performance In-Line Absolute Pressure Transmitter in the series.
EJX610A features include:
± 0.04% Accuracy
± 0.2% per 15 years Stability
90 ms Response Time
15,200 psia Maximum Over Pressure
Exida and TUV SIL 2/3 Certified
Local Parameter Setting (LPS)
SKU: n/a
Pressure Transmitter
EJX630A In-Line Mount High Performance Gauge Pressure Transmitter
The EJA430E is a high-performance gauge pressure transmitter used to measure liquid, gas, or steam pressure. Featuring Yokogawa DPharp sensor technology, the EJA430E delivers measurements accurately, quickly, and reliably.
EJA-E series models in their standard configuration, with the exception of the Fieldbus, PROFIBUS and Low Power types, are certified as complying with SIL 2 safety requirements.
Accuracy: ±0.055% of Span (Optional ±0.04%)
Response Time: 90 msec
Stability: ±0.1% of URL per 10 years
SKU: n/a
Pressure Transmitter
EJXC40A Digital Remote Sensor (DRS) Differential Pressure System
The EJXC40A Digital Remote Sensor (DRS) transmitter connects two pressure sensors, the master sensor (for high-pressure side) and remote sensor (for low-pressure side) with DRS dedicated communication cable to measure differential pressure. The DP is transmitted via a 4 to 20 mA analog signal.
EJXC40A DRS features include:
±0.056% System Accuracy*
±0.1% per 10 years Stability
250 ms Response Time
SKU: n/a
Product Carousel Tabs
Level Transmitters
ALT6100
| Type | Contacted type Level Transmitter | |
| Certificate | Ex d, KCs, CE, Rohs, IP66/67 | |
| Feature | Rod, Coxial, Cable | |
| Range | 0.15 to 20m | |
| Technology | Time Domain Refletometry(TDR) by Guided Wave Radar | |
| Applicable condition | Low Viscosity, Less Emulsion or Foam | |
| Point Feature | Liquid Application |
SKU: n/a
Level Transmitters
ALT6600
| Type | Contacted type Level Transmitter | |
| Certificate | Ex d, KCS, CE, Rohs, IP66 | |
| Feature | PVC coating | |
| Range | 0.15 to 4 meter | |
| Technology | Capacitance | |
| Applicable condition | Max 20 bar in Tank up to 100 deg C Sticky, Corrosive, no Foam, Not able to calibrate at the application | |
| Point Feature | Sticky(High Viscosity)/ Liquid/ Solid application |
SKU: n/a
Pressure Transmitter
APT3100
| Type | Pressure: Differential(DPIT), Gauge/ Absolute(PIT), Level(LIT), High Static Pressure, Flow Pressure(FIT) | |
| Certificate | SIL2 (TUV, FMEDA), Ex d, Ex ia, FM, ATEX, TR CU(EAC), INMETRO, CE, Rohs, BV, LR, KR, DNV, ABS, KCs, IP66/67, NEMA 4X | |
| Feature | 4 to 20mA, HART, Loop PoweredAccuracy ± 0.075% (option ± 0.04%) of CS* 3 lines LCD display, Self Diagnostic Function, External Buttons, DAC, Zero Trim, Eng mode
| |
| Application | Pressure, Flow, Level measurement for Oil & Gas, Liquid, Water, Maine & offshore, Vessel, Power, Chemical Plants and Refinary |
SKU: n/a
Pressure Transmitter
APT3200
| Type | Gauge/ Absolute(PIT), Level (LIT), High Static pressure | |
| Certificate | SIL2 (TUV, FMEDA), Ex d, Ex ia, FM, ATEX, TR CU(EAC), INMETRO, CE, Rohs, BV, LR, KR, DNV, ABS, KCs, IP66/67, NEMA 4X | |
| Feature | 4 to 20mA, HART, Loop PoweredAccuracy ± 0.075% (option ± 0.04%) of CS* 3 lines LCD display, Self Diagnostic Function, External Buttons, DAC, Zero Trim, Eng mode
| |
| Application | Pressure, Level measurement for Oil & Gas(up & down stream), Liquid, Water, Maine & offshore, Vessel, Power, Chemical Plants and Refinary |
SKU: n/a
Pressure Transmitter
APT3500
| Type | Pressure: Differential(DPIT), Gauge/ Absolute(PIT), Level(LIT), High Static Pressure, Flow Pressure(FIT) | |
| Certificate | SIL2 (TUV, FMEDA), Ex d, Ex ia, FM, ATEX, TR CU(EAC), INMETRO, CE, Rohs, BV, LR, KR, DNV, ABS, KCs, IP66/67, NEMA 4X | |
| Feature | 4 to 20mA, HART, Loop PoweredAccuracy ± 0.04% of CS* 3 lines LCD display, Self Diagnostic Function, External Buttons, DAC, Zero Trim, Eng mode, Gold Plate
| |
| Application | Advanced performance. Pressure, Flow, Level measurement for Oil & Gas, Liquid, Water, Marine & offshore, Vessel, Power, Chemical Plants and Refinary |
SKU: n/a
Temperature
ATT2100
| Type | Temperature Transmitter(TIT), Field Mounting Type | |
| Certificate | Ex d, FM, ATEX, TR CU(EAC), CE, KCs, IP66/67. | |
| Feature | 4 to 20mA, HART, Loop PoweredDigital Accuracy: RTD ±0.17 ℃ , T/C ±0.77 ℃ 3 lines LCD display, Self Diagnostic Function, External Buttons, DAC, Zero Trim, Eng mode
| |
| Input | RTD input: a=0.00385(KS, JIS, DIN, IEC), a=0.00391(US)Thermocouple input: KSC 1602-1982, JISC 1602-1981, ANSI MC96.1-1982 Millivolt, ohms | |
| Application | Pressure, Flow, Level measurement for Oil & Gas, Liquid, Water, Maine & offshore, Vessel, Power, Chemical Plants and Refinary |
SKU: n/a
Product Carousel Tabs
Pressure Transmitter
Capacitance Manometers
Advanced manometer technology delivers sustained vacuum accuracy.
Every vacuum pressure gauge and chamber process has a precise Torr level it must reach to sustain process yields. With industry-leading advanced sensor design features, capacitance manometers from Brooks Instrument are designed to improve manometer measurement reliability, minimize drift, resist diaphragm contamination and minimize thermal effects. And because these vacuum pressure gauges are fully digital devices, Brooks capacitance manometers operate over a wide dynamic range with extremely good accuracy. The result is an exceptionally reliable family of manometers and vacuum pressure gauges for all vacuum measurement applications.
SKU: n/a
Pressure Transmitter
Elastomer Sealed Pressure Controllers
Achieve better accuracy, stability and reliability with stable electronic pressure controllers.
Elastomer sealed pressure controllers from Brooks Instrument are designed to be rugged, durable and cost-effective while delivering the sustained and proven accuracy users worldwide count on from the leader in fluid measurement and control. Our electronic pressure controllers utilize the core control technology present in our industry-leading thermal mass flow controllers.
SKU: n/a
Pressure Transmitter
Electronic Pressure Transducers and Transmitters
Get smart, precise digital control with less drift.
For intelligent pressure transmitter devices that deliver dependable pressure monitoring in ultra-high purity applications, count on smart electronic pressure transmitters and transducers from Brooks Instrument. Wetted surface materials are selected for high corrosion resistance suitable for demanding environments. Our innovative diaphragm manufacturing process ensures less drift and lack of zero stability commonly associated with competitive pressure transducers and transmitters. And with a wide transducer pressure measurement range combined with an array of I/O options, you can cover a variety of operating conditions with a single device type to minimize inventory and operator confusion.
SKU: n/a
Pressure Transmitter
Mechanical Pressure Gauges, Regulators, Switches, Transmitters
Industrial pressure gauges with exceptional versatility and reliability to handle industrial processes.
To withstand the pressures of demanding industrial applications, pressure gauge manufacturer Brooks Instrument offers a wide range of pressure gauges, pressure regulators, pressure switches and transmitters employing durable designs and materials. Using 316L stainless steel wetted parts ensures robust, reliable performance in harsh service applications in gas panels, gas cabinets, valve manifold boxes, process analyzers and more.
SKU: n/a
Pressure Transmitter
Metal Sealed Pressure Controllers
Stable pressure control and enhanced process gas purity. Maximized process results.
Metal sealed pressure controllers from Brooks Instrument are designed to be reliable and durable while delivering the sustained and proven accuracy users worldwide count on from the leader in fluid measurement and control. Our electronic pressure controllers utilize the core control technology present in our industry-leading thermal mass flow controllers.
SKU: n/a
